This will create a new symbol in the symbol-list (see next page).Ģ8 By expanding Symbols window, you now see the full_adder as one of the symbols in the list. And select the Create Schematic Symbol under the Processes tab and click Run.
Modelsim pe graph how to#
The next two pages will show you how to create your own library (full_adder) so you can re-use them many times.Ģ7 Make sure you select the Synthesis/Implemtation drop down on the upper-left of the window. Congratulations, you now learn enough skill to do your first lab. Try zoom-out and scroll all the way to the left in the timing chart window. The ModelSim window will open.Ģ6 You are did not see any error in the Transcript window (lower window) and see only green-color simulation in the timing chart window, your simulation is successfully ran. Save your simulation (Ctrl-s) and save often.Ģ4 On the upper left window, make sure the Behavioral Simulation is selected and bottom left window, the Processes tab is showing.Ģ5 Right click on the Simulate Behavioral Model and select Run. Once you have done this, you are ready to run the simulation. Toggle the A, B, and C so that it counts from 000 to 001 to 010 to 011, all the way to 111 and back to 000 as shown above. Go ahead and click on the light-green area of the timing chart to toggle the value. In Clock Information, make sure to select Combinational (or internal clock) and click Finish.Ģ3 A window of all inputs and outputs are displayed. Click Finish.Ģ2 A new window opens to give you some setting on how long you like to simulate. Select the Test Bench WaveForm and type in full_adder_test in the File name and click Next.Ģ0 Since we want to create the test for full_adder, simply click on full_adder and then Next button.Ģ1 A quick summary screen display. You will get the following window.ġ7 On the upper left window, select the Behavioral Simulation drop-down so we can get ready to create a simulation file.ġ8 Right click on the full_adder.sch file and select New Source.ġ9 A new window opens. For upper window, click on the Sources tab, and for lower window, click on the Process tab. You should now save your work.ġ6 Because we have close down the Processes window earlier to make room for the Symbols listing, let s bring it back by Menu>View>Processes. You can also right click on the I/O port to rename.ġ5 After connecting the wire to the xor3 and renaming the port, this is our final layout of the circuit. Notice when wire did not connect to the input of a logic gate (in this case xor3). Do a little experiment here to see different way to connect wires. To connect wire, you can click once at the begin point and double-click on the end point. And use the Add I/O Marker to add inputs and outputs. Then, use the Add Wire button to add wires to the input of the xor3 gate. You can zoom in and out of this schematic editor with the zoom button.ġ4 Now we added the or3 gate and xor3 gate. This is a list of logic gates which is available for the device xa2c*.** which we originally selected by default when we started the project.ġ3 Let s select the and2 gate (2-input and-gate) and put three of them on the schematic area. Click on this button.ġ2 After closing down the left-bottom window and widen the left-panel a bit, you will see the Symbol list better. Now mouse over the tool bar with a and-gate looking symbol.
Click Finish.ġ1 A screen with a blank schematic will appear. Enter a file name called full_adder and click Next.ġ0 A quick summary is displayed. Let s build a simple full-adder.ĩ Be sure to select Schematic from the left-window list. Click Finish.Ĩ Now, you can add a new Source. So click Next to continue.ħ This is a quick summary of what you are creating for the project. Click Next to continue.Ħ You don t need to add existing files either. Click Next to continue.ĥ You don t need to create any new files at this time because you can add files later. Leave everything else as default for now.
Modelsim pe graph simulator#
1 After opening the Programs> Xilinx ISE 8.1i > Project Navigator, you will come to this screen as start-up.ģ Enter a project name and be sure to select Schematic as the Top-Level Source Type and click Next.Ĥ Make sure your Simulator is the ModelSim (PE/SE) Mixed otherwise your simulation will not work.
0 kommentar(er)
